Title: 
Safety Instructions About Forklifts

Word Count:
676

Summary:
Forklifts are industrial vehicles made to take the place of manual lifting and manual work. There are two “forks” or arms located at the front of the vehicle that are used to lift, lower, stack and unstack heavy loads. The loads are usually stacked on top of wooden pallets that the arms or forks fit into to bring a large quantity of things up or down at once. The drivers cause almost 50% of accidents involving forklifts. Normally, the driver has hit a pedestrian. Therefore, f...


Keywords:
truck,safety,automotive


Article Body:
Forklifts are industrial vehicles made to take the place of manual lifting and manual work. There are two “forks” or arms located at the front of the vehicle that are used to lift, lower, stack and unstack heavy loads. The loads are usually stacked on top of wooden pallets that the arms or forks fit into to bring a large quantity of things up or down at once. The drivers cause almost 50% of accidents involving forklifts. Normally, the driver has hit a pedestrian. Therefore, forklifts and people should not be in the vicinity of each other. 

Some other forklift related accidents include: 

Forklift tipping over and overturning 
Collision with other vehicles or stationary objects 
Part of the operator's body leaning out of the cabin and hitting an object 
The load falling off the pallets 

There are things that can be done by the employee to reduce the number of forklift accidents. First, the driver should always perform a pre-safety check of the vehicle before operating. Once the driver sees that all is in tact, while driving the vehicle the driver should use safe handling procedures of the load. This includes paying close attention to the load limit of each particular forklift. Since forklifts are a gas-powered vehicle, gasoline limits and storage should be carefully observed. In addition to safe fuel use, the battery also needs to be handled and cared for properly to ensure safety.

Here are a few safety procedures that should be followed by all employees. Some of them may seem like common sense, but they are so important that they are in need of repeating. 

Passengers on forklifts to be strictly forbidden, unless there is a separate seat provided with a restraint 
Other people kept clear when forklift is operating 
Operator should take care when moving between artificial and natural light 
Load made secure and lowered to safe centre of gravity before carrying 
Sudden stops and starts are to be avoided 
No part of the operator's body to protrude beyond the overhead protection 
Ramps not to be used unless the forklift operator is trained in their use 
Operator to remain seated and secured at all times 
Forklift to operate within a designated area, separate from pedestrians 
Operator to remain in the cabin when a forklift overturns 
Most importantly: 

PEOPLE SHOULD NEVER BE RAISED ON THE FORKLIFT OR THE PALLETS 
IF THERE IS NO OTHER WAY TO LIFT A WORKER, A PROPER WORK PLATFORM MUST BE USED 
 
In addition to checking the vehicle daily for safety hazards, the workplace should also be checked for the following: 

Power-lines 
Blind corners 
Pedestrian areas 
Low doorways 
Uneven floors 
Ramps 
Overhead pipes and fittings 
Confined spaces 
Adequate lighting 
Noise 

Above all else, a training coarse must be completed before attempting to drive or operate a forklift. Besides formal instruction, the training must include practical training (such as demonstrations) and an evaluation of the operator in the workplace to assure that he can operate the forklift safely. Initial training content must consist of both truck-related topics and workplace-related topics. 

Some truck-related topics include:

operating instructions, warnings and precautions specific to the trucks the employee will be authorized to operate 
differences between the truck and the automobile 
truck controls and instrumentation 
engine or motor operation 
steering and maneuvering 
visibility 
fork and attachment adaptation, operation and use limitations; 
vehicle capacity 
vehicle stability 
any vehicle inspection and maintenance that the operator must perform; 
refueling and/or charging and recharging of batteries 
operating limitations 
any other information from the forklift operator's manual. 
Some workplace related topics include: 

surface conditions where the vehicle will be operated 
composition of loads and load stability 
load manipulation, stacking and unstacking 
pedestrian traffic 
narrow aisles and other restricted places where the vehicle will be operated 
any hazardous (classified) locations, such as flammable storage areas, where the vehicle will be operated 
ramps and other sloped surfaces; 
closed environments and other areas where insufficient ventilation or poor vehicle maintenance could cause a buildup of carbon monoxide or diesel exhaust; and 
other unique or potentially hazardous environmental conditions in the workplace.